USED Guyatone Guyatone / EB-25 [20]
USED Guyatone Guyatone / EB-25 [20]
Item Code: 20-2800002361066
Condition:
USED
Store: [20]
fukuoka
Relation Page:
GUYATONE x USED x ELECTRIC BASS
Regular price
¥38,520 JPY
Regular price
Sale price
¥38,520 JPY
Unit price
per
If you would like to make a bank transfer, please give us an e-mail with name of your request item.
For customers residing in Japan
This Guyatone electric bass has a smaller shape with a scale of approximately 770mm.
One humbucker type pickup gives it a soft tone sound. As for adjustments, the tone pot has been replaced due to a defective tone pot, and the wiring has been corrected.
Also, the string height is high, so it has been corrected by neck ironing and shimming.
In addition, the 4th string saddle spring has been installed, and the bent saddle screws have been corrected. (The groove is a bit crushed, so it takes a lot of force to turn it.)
The truss rod has been checked to 60 degrees left and right of the rod, and the frets still stand up to cutting but will be fretted low.
There are cracks on the body side and neck joint.
Item rank: B (average)
Truss Rod : Plenty of room
Fret: 60-70%.
Attachment : Soft case / Non-genuine
Country of Origin : Japan
Weight : 3.73kg
Serial : No serial number
Truss Rod : No problem, rod is 60 degrees to the left and right.
Fretboard: Still can withstand cutting, but the frets are low.
String height(bass string side)|2.5mm above 12th fret
String height(treble string side)|2.0mm above 12th fret
Nut width|38.0mm
Neck thickness(near 1st fret)|22.0mm
Neck thickness (near 12th fret)|26.3mm
SCALE|772cm (30.4")
RADIUS|254mm (10")
Strings for setup|Aria ProII AGS-600 / .045-.100 set
Repair and maintenance parts|Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, electrical repair, fret adjustment
* The truss rod, remaining frets, string height, etc. are the setting values at the time of setup and adjustment at our repair center.
* This item is only available as a single item.
We will try to delete the product information as soon as possible, but it is not always in real time.
specs
Truss Rod
No problem, rod is confirmed to be 60 degrees to the left and right.
Fretboard Remaining
Note that the frets are low and can still withstand cutting.
String height (bass string side)
2.5mm above 12th fret
String height (treble string side)
2.0mm above 12th fret
Nut width
38.0mm
Neck Thickness (near 1st fret)
22.0mm
Neck Thickness (near 12th fret)
26.3mm
Scale
772cm (30.4")
RADIUS
254mm (10")
Strings for setup
Aria ProII AGS-600 / .045-.100 set
Repair and maintenance
Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, electrical repair, fret adjustment
One humbucker type pickup gives it a soft tone sound. As for adjustments, the tone pot has been replaced due to a defective tone pot, and the wiring has been corrected.
Also, the string height is high, so it has been corrected by neck ironing and shimming.
In addition, the 4th string saddle spring has been installed, and the bent saddle screws have been corrected. (The groove is a bit crushed, so it takes a lot of force to turn it.)
The truss rod has been checked to 60 degrees left and right of the rod, and the frets still stand up to cutting but will be fretted low.
There are cracks on the body side and neck joint.
Item rank: B (average)
Truss Rod : Plenty of room
Fret: 60-70%.
Attachment : Soft case / Non-genuine
Country of Origin : Japan
Weight : 3.73kg
Serial : No serial number
Truss Rod : No problem, rod is 60 degrees to the left and right.
Fretboard: Still can withstand cutting, but the frets are low.
String height(bass string side)|2.5mm above 12th fret
String height(treble string side)|2.0mm above 12th fret
Nut width|38.0mm
Neck thickness(near 1st fret)|22.0mm
Neck thickness (near 12th fret)|26.3mm
SCALE|772cm (30.4")
RADIUS|254mm (10")
Strings for setup|Aria ProII AGS-600 / .045-.100 set
Repair and maintenance parts|Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, electrical repair, fret adjustment
* The truss rod, remaining frets, string height, etc. are the setting values at the time of setup and adjustment at our repair center.
* This item is only available as a single item.
We will try to delete the product information as soon as possible, but it is not always in real time.
specs
Truss Rod
No problem, rod is confirmed to be 60 degrees to the left and right.
Fretboard Remaining
Note that the frets are low and can still withstand cutting.
String height (bass string side)
2.5mm above 12th fret
String height (treble string side)
2.0mm above 12th fret
Nut width
38.0mm
Neck Thickness (near 1st fret)
22.0mm
Neck Thickness (near 12th fret)
26.3mm
Scale
772cm (30.4")
RADIUS
254mm (10")
Strings for setup
Aria ProII AGS-600 / .045-.100 set
Repair and maintenance
Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, electrical repair, fret adjustment
スケールは約770mmの小ぶりなシェイプのグヤトーンのエレキベース。
ハムバッカータイプのピックアップが一つで柔らかいトーンサウンドになります。調整については、トーンポット不良のため交換済、配線修正済みです。
また、弦高が高めの為、ネックアイロン修正、シム入れにて修正しています。
その他に4弦サドルバネ取り付け、サドルネジ曲がり修正。(溝が潰れ気味なので回すのにかなり力がいります。)
トラスロッドはロッド左右60度まで確認済み、フレットはまだ切削に耐えるがフレット低めになります。
ボディサイドやネックジョイント部にヒビがあります。
商品ランク:B (並品)
トラスロッド : 余裕有り
フレット : 60~70%
付属品 : ソフトケース/非純正
生産国 : JAPAN
重量 : 3.73kg
シリアル : 無し
トラスロッド|問題なしロッド左右60度まで確認済みにて問題なし
フレット残り|注意点ありまだ切削に耐えるがフレット低め
弦高(低音弦側)|12フレット上 2.5mm
弦高(高音弦側)|12フレット上 2.0mm
ナット幅|38.0mm
ネック厚(1フレット付近)|22.0mm
ネック厚(12フレット付近)|26.3mm
スケール|772cm (30.4")
RADIUS|254mm (10")
セットアップ時の弦|Aria ProII AGS-600 / .045-.100 set
リペア・メンテナンス箇所|クリーニング・弦交換・ロッド調整・オクターブ調整・弦高調整・電装修理・フレットすり合わせ
* トラスロッド・フレット残り・弦高などは弊社リペアセンターにてセットアップ・調整時でのセッティング数値でございます。
* こちらの商品は現物1点限りでございます。
複数のモールに掲載されているため、売却に伴う商品情報の削除は迅速を心掛けておりますが必ずしもリアルタイムではございませんので、ご注文後に万一売り切れとなっておりました際は誠に申し訳ございませんがご容赦くださいませ。
specs
トラスロッド
問題なしロッド左右60度まで確認済みにて問題なし
フレット残り
注意点ありまだ切削に耐えるがフレット低め
弦高(低音弦側)
12フレット上 2.5mm
弦高(高音弦側)
12フレット上 2.0mm
ナット幅
38.0mm
ネック厚(1フレット付近)
22.0mm
ネック厚(12フレット付近)
26.3mm
スケール
772cm (30.4")
RADIUS
254mm (10")
セットアップ時の弦
Aria ProII AGS-600 / .045-.100 set
リペア・メンテナンス箇所
クリーニング・弦交換・ロッド調整・オクターブ調整・弦高調整・電装修理・フレットすり合わせ
ハムバッカータイプのピックアップが一つで柔らかいトーンサウンドになります。調整については、トーンポット不良のため交換済、配線修正済みです。
また、弦高が高めの為、ネックアイロン修正、シム入れにて修正しています。
その他に4弦サドルバネ取り付け、サドルネジ曲がり修正。(溝が潰れ気味なので回すのにかなり力がいります。)
トラスロッドはロッド左右60度まで確認済み、フレットはまだ切削に耐えるがフレット低めになります。
ボディサイドやネックジョイント部にヒビがあります。
商品ランク:B (並品)
トラスロッド : 余裕有り
フレット : 60~70%
付属品 : ソフトケース/非純正
生産国 : JAPAN
重量 : 3.73kg
シリアル : 無し
トラスロッド|問題なしロッド左右60度まで確認済みにて問題なし
フレット残り|注意点ありまだ切削に耐えるがフレット低め
弦高(低音弦側)|12フレット上 2.5mm
弦高(高音弦側)|12フレット上 2.0mm
ナット幅|38.0mm
ネック厚(1フレット付近)|22.0mm
ネック厚(12フレット付近)|26.3mm
スケール|772cm (30.4")
RADIUS|254mm (10")
セットアップ時の弦|Aria ProII AGS-600 / .045-.100 set
リペア・メンテナンス箇所|クリーニング・弦交換・ロッド調整・オクターブ調整・弦高調整・電装修理・フレットすり合わせ
* トラスロッド・フレット残り・弦高などは弊社リペアセンターにてセットアップ・調整時でのセッティング数値でございます。
* こちらの商品は現物1点限りでございます。
複数のモールに掲載されているため、売却に伴う商品情報の削除は迅速を心掛けておりますが必ずしもリアルタイムではございませんので、ご注文後に万一売り切れとなっておりました際は誠に申し訳ございませんがご容赦くださいませ。
specs
トラスロッド
問題なしロッド左右60度まで確認済みにて問題なし
フレット残り
注意点ありまだ切削に耐えるがフレット低め
弦高(低音弦側)
12フレット上 2.5mm
弦高(高音弦側)
12フレット上 2.0mm
ナット幅
38.0mm
ネック厚(1フレット付近)
22.0mm
ネック厚(12フレット付近)
26.3mm
スケール
772cm (30.4")
RADIUS
254mm (10")
セットアップ時の弦
Aria ProII AGS-600 / .045-.100 set
リペア・メンテナンス箇所
クリーニング・弦交換・ロッド調整・オクターブ調整・弦高調整・電装修理・フレットすり合わせ
Payment and Shiping
Products are shipped from Japan after the order is processed, Shipping costs are calculated automatically at the checkout page when you select your destination. , Ship worldwide by Japan Post.
Founded in 1938, Ishibashi Music Corporation is one of the busiest and most respected Musical Instrument retail chains in Japan. The company is highly regarded world wide as a reliable seller of top quality secondhand items too. We have over 13 stores around Japan including Tokyo, Yokohama, Chiba, Nagoya, Osaka, Hiroshima,Fukuoka and Shanghai(China). Ishibashi Music Corporation also handles large amounts of NEW, USED and VINTAGE instruments.
ABOUT US
Sale
-
USED ORFELD GUITARS / Ellie Korina [06]
Item Code : 06-2800002032300Regular price ¥175,100 JPYRegular priceUnit price per -
USED KILLER / KG-Serpent Galaxy Black [06]
Item Code : 06-2800002067647Regular price ¥57,780 JPYRegular priceUnit price per -
USED FENDER JAPAN / ST62G-65 TRG [06]
Item Code : 06-2800002004505Regular price ¥94,500 JPYRegular priceUnit price per -
USED GIBSON / 1967 EB-0 Cherry [06]
Item Code : 06-2800002092663Regular price ¥247,200 JPYRegular priceUnit price per -
USED MOON / JJ5 ASH WHITE PG [06]
Item Code : 06-2800002050151Regular price ¥175,100 JPYRegular priceUnit price per -
USED Gibson / Limited Edition of 20 J-45HB 2009 [08]
Item Code : 08-2100000691302Regular price ¥433,349 JPYRegular priceUnit price per -
USED ZILDJIAN / Late50s A Small Stamp 18" 1952g Old A Ride Cymbal [08]
Item Code : 08-2100000692040Regular price ¥33,705 JPYRegular priceUnit price per -
USED ZILDJIAN / Trans Stamp 20" Ride 2092g w/Sizzle Hole Old A Zildjian [08]
Item Code : 08-2100000691944Regular price ¥76,602 JPYRegular priceUnit price per -
USED GIBSON / EB-0 [05]
Item Code : 05-2100000691982Regular price ¥209,811 JPYRegular priceUnit price per -
USED FENDER / 1966 PRECISION BASS SUNBURST [05]
Item Code : 05-2100000692026Regular price ¥1,224,000 JPYRegular priceUnit price per